Video Processors for Private Theaters
The video processor is the one component nobody sees and every frame passes through. This is how Blackroom uses madVR Envy and Lumagen to fit HDR into the light a projector can actually deliver — in the room it will live in.
Tell us about your room. We will show how this fits into your system — and where it is not needed.
A desert at noon. The sun hangs over the dunes, and you can still read the ripples in the sand beneath it — nothing has burned out to white. A cut to the cave: a face in near-darkness, and you see the eyes, the stubble, the sweat. Your pupils open with the scene, as they would on location.
That balance is not in the film file. The movie was graded for a monitor that reaches 1,000 nits and more; the projector in a private theater delivers a fraction of that. Something has to translate one into the other, frame by frame, without changing what the colorist approved. That is the job of the video processor — and we treat it as part of one system with the projector, the screen and the calibration, never as a box added at the end.
Built-in tone mapping or an external processor
Every reference projector we specify already tone-maps HDR on its own. JVC’s Frame Adapt HDR analyzes the image dynamically, and Sony and Barco have their own HDR processing. The question is not whether HDR gets mapped, but how much computing power and control stand behind it.
The numbers we set in the processor
CTA/CEDIA-CEB23-B, the Home Theater Video Design recommended practice, sets out the geometry and lighting of a theater; CEDIA’s RP23 for immersive video is in development, and Blackroom’s founder Anton Zadnepryannyy sits on a CEDIA committee developing industry standards. Inside that framework, the processor receives the real numbers of the room — measured on the screen, after the projector is installed:
- 1,000–4,000 nits — peak brightness HDR films are mastered for
- 108 nits — HDR target in a private theater
- 3.2 stops — compression for a 1,000-nit master at 108 nits
The arithmetic explains why this matters. A film mastered at 1,000 nits shown at 108 nits must fit 9.3 times the range — about 3.2 stops. A 4,000-nit master needs 37 times, or 5.2 stops. At 4K and 60 frames per second, the processor makes that decision for 3840 × 2160 × 60 pixels: almost half a billion every second. A static curve compresses every scene the same way; a dynamic one spends the projector’s light where each shot needs it.
On high-output systems a processor can hold several brightness presets — from 108 to 500 nits — each with its own tone-mapping curve, chosen for the film, the room and the people in it.
Dolby Vision
There is no native Dolby Vision for home projectors, and no home video processor decodes it in full. Lumagen and madVR Envy can accept player-led Low-Latency Dolby Vision from some sources, but the tone mapping is still done by the processor. That is why we do not chase the logo: frame-by-frame dynamic tone mapping does the same work, calibrated to the light on your screen.
The processors we specify
Two external platforms cover our theaters, and the built-in processing of the projector stays as the baseline.
madVR Envy: Core, Pro, Extreme
GPU-based processing with patented dynamic tone mapping, machine-learning upscaling, HDMI 2.1 at 48 Gbps and 3D LUTs up to 256 points per axis. High-output Barco and Christie systems, curved or architectural screens, theaters that double as gaming rooms.
Lumagen Radiance Pro
FPGA-based processing with dynamic tone mapping, true genlock for exact lip-sync, a 3 ms game mode and 4,913-point 3D LUT calibration. Scope screens with masking and systems built for long-term stability.
Projector built-in: JVC Frame Adapt HDR
Dynamic tone mapping inside the projector. Media rooms and compact theaters, with rack space reserved for an external processor.
Built-in tone mapping on a reference projector is good. An external processor has far more computing power, and in the hardest scenes — bright sky over dark ground, a lamp in a black room — that is where detail survives or disappears. We never use a processor to make the picture “punchier”. Its job is to deliver what the colorist approved.
How we build it into the room
In the BIM model the processor has a fixed place: in the equipment rack, between the sources and the projector, with its own ventilation. A GPU-based processor produces real heat, and the rack is engineered as part of the climate system, so the theater stays silent and the electronics stay cool.
The processor is wired into the control system, not left to a remote. When it detects a 2.39:1 film, the RTI, KNX or Lutron scenario moves the screen masking, and on scope screens the projector’s lens memory or the processor’s scaling sets the image to constant height. Read more on our Cinemascope screens and masking systems pages. Audio delay is programmed so that dialogue stays on the actor’s lips.
Processing in two of our rooms
Apex Cinema — CEDIA Awards Winner 2025
An RGB laser projector already has the brightness that makes HDR easy. The reserved processor is the next step: it will take the last reserve of contrast and highlight detail out of the Barco without touching the room.
Millennium Park — CEDIA Highly Commended 2024
A media room lives with daylight scenarios, sport and games as well as films. Here the projector’s own dynamic tone mapping carries HDR, and the calibration does the rest.
A processor or a brighter projector
Light and processing solve the same problem from two ends. At 500 nits, a 1,000-nit master needs only one stop of compression; at 108 nits it needs more than three. A brighter projector reduces the work, and the processor finishes it. That is why we choose them together — read more on our 4K and 8K projectors page.
Frequently asked questions
Do I need a video processor if my projector has its own tone mapping?
Not always. Built-in tone mapping on JVC, Sony and Barco reference projectors is good. An external processor adds more computing power, separate control of shadows and highlights, automatic aspect-ratio handling and deeper calibration. In a dedicated private theater it is the step that takes the last reserve out of the projector.
madVR Envy or Lumagen?
Both deliver frame-by-frame dynamic tone mapping. madVR Envy is GPU-based, with machine-learning upscaling and full 48 Gbps HDMI 2.1. Lumagen is FPGA-based, with true genlock and direct masking control. We choose by the room, the screen and the projector.
Does a video processor support Dolby Vision?
No home processor decodes full Dolby Vision, and home projectors do not support it natively. Some sources can send player-led Low-Latency Dolby Vision, but the processor still does the tone mapping. Dynamic tone mapping calibrated to your screen does the same job for each scene.
Does a video processor add input lag for gaming?
Very little. Lumagen’s game mode adds 3 ms with all processing enabled. The latest madVR Envy models support HDMI 2.1 at 48 Gbps with variable refresh rate for consoles and gaming PCs.
Do I need a video processor for a MicroLED wall or a TV?
Less often. With 1,000–4,000 nits, a MicroLED wall needs little tone mapping. A processor still helps with upscaling, aspect ratio and one consistent calibration for every source.
Can a processor be added to an existing theater?
Yes, if the rack, ventilation and HDMI cabling allow it. We reserve space for it in new theaters, as in Apex Cinema. The processor also stays when the projector is replaced: it is recalibrated for the new one.
%25D0%25B1.jpeg)